Vector files for vinyl cutting
A plotter follows outlines. Trace the artwork into a small number of closed, disjoint shapes — one per colour of vinyl — with nothing too thin to weed.
- Ön ayar
- Vinil
- Palet
- 4 renk
- Çıktı
- SVG
- Fiyat
- Ücretsiz önizleme
Bir görseli buraya bırakın veya yapıştırın
Görseliniz asla yüklenmez. Bu sekmede çizilir.Tam dönüştürücüyü aç
Ön ayar
- 01Logo16 renk
- 02Çizgi sanatıSiyah beyaz
- 03Fotoğraf64 renk
- 04Nakış8 renk · Kesim
- 05Vinil — bu sayfa için ayarlandı4 renk · Kesim
- 06LazerSiyah beyaz · Çokgen
- Çıktı · SVG · PDF · EPS · DXF
- Önizleme ücretsiz · Pro ile indirme ayda €9,00
- Dosyanız bu sekmede kalır
Yazılımın ihtiyaç duyduğu
- One layer per colour
- Each colour is a separate sheet of vinyl, cut separately and layered by hand. Cutout mode produces exactly that: disjoint regions with no overlap to register.
- Nothing too thin to weed
- Thin slivers and single-pixel bridges cut fine and lift with the waste. The preset filters small regions and drops short edges before they become cut paths.
- Closed contours with correct holes
- The counter of an O has to be its own contour or the blade never cuts it out. Traced region boundaries are closed by construction.
- No fills, no strokes, no effects
- A plotter ignores everything except the path. Drop shadows and outlines from the source image become extra cut shapes, so remove them before tracing rather than after.
- A size decided before the cut
- Scaling after tracing scales the smallest features too. Set the physical size first and check the thinnest part at that size.
Ön ayar
The vinyl preset traces four colours in cutout mode with a heavy speckle filter and a long minimum edge. Every one of those numbers is about weeding: a sliver two pixels wide is a path the blade will cut and your tweezers will tear.
Neden vectortrace
- Fiş 1 / 3
Tarayıcı içi ve özel
Motor, kendi makinenizde bir çalışanda çalışan WebAssembly'dir. Görseliniz asla yüklenmez — bu yüzden sızdırılacak bir şey, silinecek bir şey ve güvenilecek bir şey yoktur.
- Fiş 2 / 3
Bir sarmalayıcı değil, düzenlenebilir yollar
Motor, görseli renk bölgelerine ayırır, aralarındaki sınırı alır ve ona eğriler oturtur. Ortaya çıkan gerçek geometridir — bölge başına tek dolgu, her düğüm sizin taşımanız için — sekmede üretilir ve asla sunucuda değil.
- Fiş 3 / 3
Baskı ve üretimin kullandığı biçimler
Eser için SVG ve PDF; kesiciler, gravür makineleri ve nakış yazılımları için EPS ve DXF. Illustrator, Inkscape ve LibreCAD'de açılan gerçek dosyalar — içinde JPEG olan bir SVG değil.
Kıyaslama
Ölçüldü, pazarlanmadı. Külliyat, yöntem ve koşunun ürettiği her rakam tam olarak yayımlanır.
Yöntem → /benchmarks- boundary error, p95
- 0.09 px
- region-count error
- 0.000
- node-count ratio
- 1.00×
Sorular
- 01Does the SVG import into Cricut Design Space or Silhouette Studio?
- Both read SVG. Silhouette Studio also reads DXF in some editions. Import the SVG, confirm the size in the software, and check the smallest feature at that size before you cut.
- 02Why are there tiny shapes in my cut file?
- They are small regions the tracer found and kept. Raise the speckle filter until they disappear from the path count — deleting them by hand afterwards is slower and easy to get half-right.
- 03Can I cut a photograph?
- You can cut a posterisation of one. Trace with two to four colours and treat it as a stencil; a photograph has no natural boundaries to cut along, so the result is a design decision rather than a reproduction.