Vector files for embroidery digitizing
Digitizing starts with clean shapes. Trace the artwork into closed, disjoint paths with a thread-count palette, then hand it to your digitizing software.
- 프리셋
- 자수
- 팔레트
- 8색
- 출력
- SVG
- 가격
- 무료 미리보기
이미지를 여기에 놓거나 붙여넣으세요
이미지는 업로드되지 않습니다. 이 탭에서 트레이싱됩니다.전체 변환기 열기
프리셋
- 01로고16색
- 02선화흑백
- 03사진64색
- 04자수 — 이 페이지에 설정됨8색 · 컷아웃형
- 05비닐4색 · 컷아웃형
- 06레이저흑백 · 폴리곤
- 출력 · SVG · PDF · EPS · DXF
- 미리보기 무료 · 다운로드는 Pro 월 €9.00
- 파일이 이 탭 안에 머뭅니다
소프트웨어가 필요로 하는 것
- Closed paths
- Every shape has to be a closed outline. An open stroke has no interior, and a fill stitch needs an interior to fill.
- No stacked fills
- Cutout mode gives one region per colour with nothing underneath it. Stacked output hides a full-size background shape under the artwork, and the machine stitches all of it.
- Few colours
- One colour is one thread change. The preset caps the palette at eight; drop it further to match the thread chart you actually have on the machine.
- No detail below the stitch minimum
- A shape narrower than a satin stitch cannot be sewn and will pucker the fabric. Speckle filtering removes those regions before they reach the digitizer.
- Real size, decided early
- A mark that reads at 120 mm across a jacket back does not read at 40 mm on a cap. Decide the sewn size before simplifying, because the simplification budget depends on it.
프리셋
The embroidery preset traces in cutout mode with a small palette and a heavy speckle filter. Cutout matters more than anything else here: stacked regions mean the machine stitches the same ground twice, once under the shape on top of it. Disjoint regions mean one pass per colour.
vectortrace를 선택하는 이유
- 전표 1 / 3
브라우저 내 실행, 완전한 비공개
엔진은 여러분의 기기에서 워커로 실행되는 WebAssembly입니다. 이미지는 업로드되지 않으므로 유출될 것도, 삭제할 것도, 믿고 맡길 것도 없습니다.
- 전표 2 / 3
감싼 것이 아니라 편집 가능한 패스
엔진은 이미지를 색상 영역으로 그룹화하고, 그 경계를 추출해 곡선을 피팅합니다. 결과물은 실제 지오메트리입니다 — 영역마다 하나의 채우기, 여러분이 직접 옮길 수 있는 모든 노드 — 탭 안에서 만들어지며 서버에서는 결코 만들어지지 않습니다.
- 전표 3 / 3
인쇄와 생산 현장에서 쓰는 형식
아트워크용 SVG와 PDF, 커터·조각기·자수 소프트웨어용 EPS와 DXF. Illustrator, Inkscape, LibreCAD에서 바로 열리는 실제 파일 — JPEG를 감싼 SVG가 아닙니다.
벤치마크
마케팅이 아니라 측정입니다. 코퍼스, 방법론, 그리고 실행이 만들어낸 모든 수치를 빠짐없이 게시합니다.
방법론 → /benchmarks- boundary error, p95
- 0.09 px
- region-count error
- 0.000
- node-count ratio
- 1.00×
질문
- 01Does this produce a stitch file — DST, PES, EXP?
- No. It produces the clean vector artwork that a digitizing package turns into stitches. Stitch generation is where underlay, pull compensation and density live, and those are decisions about a specific fabric and a specific machine.
- 02Why does cutout mode matter so much for embroidery?
- Because stacked tracing paints regions over each other. The bottom region is still full size underneath, so the machine sews the whole background and then sews the artwork on top of it — double the stitches and a stiff, puckered patch.
- 03How many colours should I trace to?
- The number of threads you are willing to change. Four to six is normal for a logo. Trace to that number rather than trimming afterwards, so the tracer decides which shades merge.