Vector files for vinyl cutting
A plotter follows outlines. Trace the artwork into a small number of closed, disjoint shapes — one per colour of vinyl — with nothing too thin to weed.
- 프리셋
- 비닐
- 팔레트
- 4색
- 출력
- SVG
- 가격
- 무료 미리보기
이미지를 여기에 놓거나 붙여넣으세요
이미지는 업로드되지 않습니다. 이 탭에서 트레이싱됩니다.전체 변환기 열기
프리셋
- 01로고16색
- 02선화흑백
- 03사진64색
- 04자수8색 · 컷아웃형
- 05비닐 — 이 페이지에 설정됨4색 · 컷아웃형
- 06레이저흑백 · 폴리곤
- 출력 · SVG · PDF · EPS · DXF
- 미리보기 무료 · 다운로드는 Pro 월 €9.00
- 파일이 이 탭 안에 머뭅니다
소프트웨어가 필요로 하는 것
- One layer per colour
- Each colour is a separate sheet of vinyl, cut separately and layered by hand. Cutout mode produces exactly that: disjoint regions with no overlap to register.
- Nothing too thin to weed
- Thin slivers and single-pixel bridges cut fine and lift with the waste. The preset filters small regions and drops short edges before they become cut paths.
- Closed contours with correct holes
- The counter of an O has to be its own contour or the blade never cuts it out. Traced region boundaries are closed by construction.
- No fills, no strokes, no effects
- A plotter ignores everything except the path. Drop shadows and outlines from the source image become extra cut shapes, so remove them before tracing rather than after.
- A size decided before the cut
- Scaling after tracing scales the smallest features too. Set the physical size first and check the thinnest part at that size.
프리셋
The vinyl preset traces four colours in cutout mode with a heavy speckle filter and a long minimum edge. Every one of those numbers is about weeding: a sliver two pixels wide is a path the blade will cut and your tweezers will tear.
vectortrace를 선택하는 이유
- 전표 1 / 3
브라우저 내 실행, 완전한 비공개
엔진은 여러분의 기기에서 워커로 실행되는 WebAssembly입니다. 이미지는 업로드되지 않으므로 유출될 것도, 삭제할 것도, 믿고 맡길 것도 없습니다.
- 전표 2 / 3
감싼 것이 아니라 편집 가능한 패스
엔진은 이미지를 색상 영역으로 그룹화하고, 그 경계를 추출해 곡선을 피팅합니다. 결과물은 실제 지오메트리입니다 — 영역마다 하나의 채우기, 여러분이 직접 옮길 수 있는 모든 노드 — 탭 안에서 만들어지며 서버에서는 결코 만들어지지 않습니다.
- 전표 3 / 3
인쇄와 생산 현장에서 쓰는 형식
아트워크용 SVG와 PDF, 커터·조각기·자수 소프트웨어용 EPS와 DXF. Illustrator, Inkscape, LibreCAD에서 바로 열리는 실제 파일 — JPEG를 감싼 SVG가 아닙니다.
벤치마크
마케팅이 아니라 측정입니다. 코퍼스, 방법론, 그리고 실행이 만들어낸 모든 수치를 빠짐없이 게시합니다.
방법론 → /benchmarks- boundary error, p95
- 0.09 px
- region-count error
- 0.000
- node-count ratio
- 1.00×
질문
- 01Does the SVG import into Cricut Design Space or Silhouette Studio?
- Both read SVG. Silhouette Studio also reads DXF in some editions. Import the SVG, confirm the size in the software, and check the smallest feature at that size before you cut.
- 02Why are there tiny shapes in my cut file?
- They are small regions the tracer found and kept. Raise the speckle filter until they disappear from the path count — deleting them by hand afterwards is slower and easy to get half-right.
- 03Can I cut a photograph?
- You can cut a posterisation of one. Trace with two to four colours and treat it as a stencil; a photograph has no natural boundaries to cut along, so the result is a design decision rather than a reproduction.